Step 1

Measure the cover to determine the exact overlap

5 x 5 strap spacing will have approximately 12" of overlap. This may vary between 10 and 15 inches

3 x 3 strap spacing will have approximately 18" of overlap. This may vary between 15 and 22 inches

  Step 2

Stretch the cover over the pool and use buckets of water to hold it in place. Adjust for correct overlap on all sides. If the cover has cutouts, adjust for proper alignment now.

  Step 3

Anchor points should be located 18" form the edge of the cover (not the edge of the pool) and in line exactly with the strap.

See page 3 for instructions on how to install anchors. Begin installing anchors as shown below :

Install springs on the straps for which you have just installed anchors. Tighten straps untill springs are compressed 50%

  Step 5 (Optional)

Snap a chalk line 18 inches from the edge of the cover on all four sides. (This should be in line with the anchors you just installed) This will be your anchor line and ensures that all anchors will be aligned.

  Step 6

With the center straps of the cover secured, work your way to the corners as shown below :

  Step 7

Inspect your installation. Make sure that all springs are no more than 50% compressed and that the cover is taut across the pool.

  Step 1

Stretch the cover over the pool and use buckets of water to hold it in place. Adjust for correct overlap on all sides. If the cover has cutouts, adjust for proper alignment now

  Step 2

Anchor points should be located 18" from the edge of the cover (not the edge of the pool) and in line exactly with the strap.

See page 3 for instructions on how to install anchors. Begin installing anchors as shown below : 

 
 

  Step 3

Install springs on the straps for which you have just installed anchors. Tighten straps untill springs are compressed 50%

  Step 4

With the center straps of the cover secured, install the rest of the anchors as shown below :

  Step 5

Inspect your installation. Make sure that all springs are no more than 50% compressed and the cover is taut across  the pool.

  Concrete Decks :

  Step 1

Using a rotary hammer drill with a 3/4 inch masonry bit, drill about 3 inches into the deck

  Step 2

Put the brass casing into the hole and tamp it down lightly with the Tamper Tool untill flush with the deck. Do not pound the anchor in with the anchor insert in place.

  Step 3

Screw the brass insert into the casing leaving about 1/3 of the anchor insert above the deck to secure the spring

  Wood Decks :

  Step 1

Using a drill with a 1 1/2 inch self-boring bit, countersink a hole 1/8 inch deep into wood deck.

  Step 2

Directly in the center of that hole, drill a 3/4 inch diameter hole into the deck at least 2 inches deep

  Step 3

Insert the flange portion of the anchor into the deck and secure to deck with wood screws provided

  Step 4

Screw the insert into the flange leaving about 1/3 of the anchor above the deck to secure the spring.

Decks made with brick or stone require a steel sleeve to support anchors. These may be made from 3/4" inside diameter conduit cut in 14"-18" pieces

  Step 1

Using a rotary hammer drill with 1 inch masonry bit, drill through brick or stone to soft ground. (Be careful not to crack bricks or stone when drilling)

  Step 2

Tap anchor into end of conduit.

  Step 3

Using a block of wood and a hammer, drive the anchor sleeve into the ground flush with the deck.

  Step 4

Screw the brass insert into the casing leaving about 1/3 of the anchor above the deck to secure the spring

  Lawn or Planters :

The above method can be used in lawn or planters only if 10% or less of the straps are anchored in this manner
 
 
 
 
 
 

Walls, waterfalls, or elevated spas must be treated specially since there is no deck available to secure an anchor. Eyebolts will be needed to install a cover in these areas and are not supplied by Rayner. Due to the many different possibilities, the specific eyebolt necessary must be determined on site.

When installing a cover with a raised area, this section of the cover must be installed first.

  Step 1

Locate the section of the cover showing no straps. You will find a d-ring with a carabineer under the edge of the cover

  Step  2

Stretch the cover over the pool making sure that it is positioned correctly in the raised wall area. Use buckets of water to hold the cover in place around the pool. Adjust for exact overlap on all sides with sufficient deck. Remember, there will be no overlap in raised wall area.

  Step 3

Determine where the eyebolts will be drilled into the obstruction based on the carabineer locations. Install eyebolts as per the manufacturer's instructions.

  Step 4

Snap the cover to the eyebolts and then proceed with the standard installation for the rest of the cover.

  Step 1

Pull end of strap through first opening in buckle

  Step 2

Continue down through middle opening

  Step 3

Place flat end of spring on strap

  Step 4

Pull strap back up through middle

  Step 5

Finally, pull strap down through remaining opening